====== Ultimaker Cura 4.8 Settings ======

Cette page rassemble les settings de Cura 4.8 : j'ai des problèmes de migration de la 4.2 (dernière stable à fonctionner correctement avec ma DE200) à la 4.8

===== Default Settings 4.8 =====

Pour la 4.8 et la DE200, voici les settings de base : 

Start G-Code : 
<code>
;Begin Start Gcode for Dagoma DiscoEasy 200
;Sliced: {date} {time}
;Initial extruder: {initial_extruder_nr}

G90 ;Absolute positioning
M106 S255 ;Fan on full
G28 X Y ;Home stop X Y
G1 X100 ;Centre back during cooldown in case of oozing
M109 R{material_standby_temperature} ;Cooldown in case too hot
G28 ;Centre
G29 ;Auto-level
M104 S{material_print_temperature_layer_0} ;Pre-heat
M107 ;Fan off
G0 X100 Y5 Z0.5 ;Front centre for degunk
M109 S{material_print_temperature_layer_0} ;Wait for initial temp
M83 ;E Relative
G1 E10 F200 ;Degunk
G1 E-3 F5000 ;Retract
G0 Z3 ;Withdraw
M82 ;E absolute
G92 E0 ;E reset
G1 F6000 ;Set feedrate

;Finish Start Gcode for Dagoma DiscoEasy 200
</code>

End G-Code : 
<code>
;Begin End Gcode for Dagoma DiscoEasy 200

M106 S255 ;Fan on full
M104 S0 ;Cool hotend
;M140 S0 ;Cool heated bed
G91 ;Relative positioning
G1 E-3 F5000 ;Retract filament to stop oozing
G0 Z+3 ;Withdraw
G90 ;Absolute positioning
G28 X Y ;Home
M109 R{material_standby_temperature} ;Wait until head has cooled to standby temp
M107 ;Fan off
M18 ;Stepper motors off

;Finish End Gcode for Dagoma DiscoEasy 200
</code>


===== Settings 4.2 (fonctionnent correctement) =====

Start G-Code : 

<code>
G90                    ; Absolute positioning
M106 S255              ; Fan on full
G28 X Y                ; Home stop X Y
G1 X50                 ; Center back during cooldown in case of oozing (50??)
M109 R90               ; Cool down in case too hot
G28                    ; Center
M104 S{material_print_temperature_layer_0} ; Pre-heat
G29 P3                 ; Auto-level, 9 points
M107                   ; Fan off
G1 X100 Y20 F3000      ; Front center for degunk. G1 not G0??
G1 Z0.5
M109 S{material_print_temperature_layer_0}    ; wait for initial Temp
M82                    ; E absolute
G92 E0                 ; E Reset
G1 F200 E10            ; Degunk 
G92 E0                 ; Extruder reset
G1 Z3                  ; Withdraw
G1 F6000               ; Set feedrate
</code>

End G-Code : 

<code>
M107            ; Fan off
M104 S0         ; Stop Heating (Temp to zero)
M106 S255       ; Fan to Max
M140 S0         ; Bed Temp to zero (useless on DE200)
G91             ; Set all axes to relative
G1 E-1 F300     ; Retract by 1 (E)
G1 Z+3 F3000    ; Move up by 3 (Z)
G90             ; Set all axes to absolute
G28 X Y.        ; Go to origin on X Y axes
M107            ; Fan off
M84             ; Disable Steppers
M82             ; absolute extrusion mode
M104 S0         ; Stop Heating again... 
</code>